Harga | Rp Hubungi Kami @ RTK GNSS modules for UAV mapping Positioning with centimeter accuracy in RTK and PPK. For precise UAV ma... |
Kategori | Produk |
Share | |
Hubungi Kami | |
BELI |
Review Jual Emlid Reach M2 Ori di Makassar | Distributor
Rp Hubungi Kami @
RTK GNSS modules for UAV mapping
Positioning with centimeter accuracy in RTK and PPK.
For precise UAV mapping with less GCPs
PPK mapping with centimeter accuracy. Use fewer GCPs
Why camera synchronization is so important
Usually autopilot triggers the camera and records the coordinate it has at that moment. When the drone is flying at 20 m/s and GPS works at 5 Hz, that means your autopilot will have position readings only each 4 m, which is not suitable for precise georeferencing. In addition, there is always a delay between the trigger and the actual moment the photo is taken.
Reach eliminates the delay
Reach solves the problem of positioning by connecting directly to the camera hot shoe port, which is synced with the shutter. The time and coordinates of each photo are logged with a resolution of less than a microsecond. This method allows GCPs to be used only to check your accuracy.
1. Connect Reach to a hot shoe port on a camera
Every time a photo is taken camera produces a pulse on a flash hot-shoe connector which is synced to a shutter opening.
2. Fly a drone, Reach will record photo events
Reach captures flash sync pulses with sub-microsecond resolution and stores them in a raw data RINEX log in the internal memory.
3. Download logs from Reach and base station
After the flight, get the RINEX logs from your airborne Reach module and a base station (Reach RS, CORS or another receiver).
4. Process logs and get a file with geotags of photos
Process RINEX files using free RTKLIB software. The produced file with precise coordinates of the photos can be used for georeferencing.
NTRIP or another Reach as a base station
To calculate centimeter-precise coordinates in PPK and RTK, Reach needs corrections from a base station. It could be either another Reach receiver or an NTRIP service. VRS is also supported.
Compatibility
Reach M2 and M+ work seamlessly with other Reach receivers over any link and are compatible with any other receiver that supports RTCM3 and NTRIPChoosing between
Reach M+ and Reach M2
Reach M+ and Reach RS+
If you work within short baselines, then Reach M+ is an optimal choice.
Up to 10 km
Up to 20 km
1-2 min
Single-band
Up to 14 Hz
up to 10 Hz now
Comes with an app
ReachView is the most user-friendly
software for data collection that is available both for Android and iOS.
With ReachView, you can control all the features of Reach receivers,
such as setting up a base station, logging RINEX data, configuring NMEA
output, and monitoring data.
Camera
control
Reach is able to trigger cameras as well as register events. The event mark feature is a must for aerial mapping as it allows the precise time when the shutter was activated to be registered.
Simple log
management
Logs are automatically recorded directly to RINEX in the internal memory. View a list of the logs and download them using the ReachView app.
Monitoring
data
ReachView shows current satellite levels, your location on a map, and much more.
Reach in action
Luke Wijnberg, 3DroneMapping
As a brief synopsis of the results, the maximum deviation of points was no more than 0.09m in all axes. This is an incredible result given the fact that the average pixel size of the resulting imagery was 0.045m. The average mean error in all axes is just few mm!
Tuffwing gets 4cm precision without GCPs with Emlid Reach RTK
Brian Christal, Tuffwing
Tuffwing recently performed integration of Emlid Reach RTK to enable precision maps to be made without the use of GCPs. The system has been benchmarked by comparing a direct georeferenced model with a set of GCPs, used solely for error detection purposes. The lateral RMS error achieved is just 4cm according to the Pix4D quality report.